Measuring and Cutting

Measure the distance from baseboard to ceiling line in several different spots around the room. You will probably find that the wall is higher in some spots than others. Make a note of the maximum height.

Add 4 inches to the maximum wall height. This extra 4 inches will give you at least 2 inches extra to work with at both the ceiling line and baseboard (for trimming or for uneven walls). 

Use this measurement to cut the first strip of wallpaper and to cut each subsequent marching strip. 

Before cutting the first strip, check the position of the pattern at the ceiling line. Hold wallpaper against the wall until you find the best point for a pattern break.

Mark the wallpaper where the strip ends at the ceiling line and baseboard. Remove it to the pasting table or a clean, flat area for cutting.

Remember to add 2 inches to both the top and bottom of the strip before cutting.

Cut the second strip after matching the pattern to the first strip. Mark the top of your strips "T" on the back and number them. After cutting the first two strips, cut and paste just one strip at a time.

Evaluating Layout

Before cutting the first strip of wallpaper, examine your rolls to check the nature of the match of the pattern. Your wallpaper is designed to match in one of the following ways:

In a straight-across match, the pattern continues directly across the strips. the same part of the pattern in the first and following strips should always the same distance from the ceiling.

In a drop match, the pattern runs diagonally across the wall. Every other strip is the same at the ceiling line. 

A random (or plain) match does not present a matching up a problem,but the final result may look better if every other strip is reserved top of bottom. 

To estimate the number of strips you will need to cut, measure and mark strip widths on the walls.
 

Preparing your walls before put the wallcover

Before you work, firstly you identify your wall.

Previously wallpapered walls :

Old wallpaper should be removed unless it is in excellent condition. Wallpaper designated as strippable is easily removed by lifting a corner and pulling. Unstrippable wallpaper should be sanded, saturated with water with a sponde or sprayer, then scraped off with a putty knife. Walls should be washed and rinsed clean of the old paste. Finally, apply sizing.

Flat painted walls :

After washing, scrape or sand off any rough spots. Fill cracks and holes with lightweight spackling compound, let dry and then sand until smooth. Prime all spackled areas before applying sizing.

Glossy painted walls :
After washing, glossy surfaces should be throoughly sanded, then sized.

New and unpainted walls :

Do not apply wallpaper over new drywall or plaster without first applying a primer or sealer. Then apply sizing, this improves adhesion and provides a smooth surface for easier positioning and hanging. Badly cracked plaster walls, concrete block and paneled walls should be covered with wallpaper liner before sizing to create an even surface.

 

How to attach the drapery and the lining

After you have made the drapery, now we will attach the draperu into the lining.

1. Lay the drapes right side up on a table. 

2. Lay the lining right-side down on top of the drape so that it is about 1 1/2 inch above the bottom of the drape fabric.

3. Attach the raw sides of fabric together with pins and then stitch down along the sides 1 1/2 inches from the raw edge. Since the lining is not as wide as the drape, you will have extra drape material. This is correct.

4. Turn the drape inside out so that the right side of the drape is visible. 

5. Iron the drape, with the lining side up. You need to iron so that even amounts of drape are visible on each side of the lining. 

6. Tuck the extra drape material under itself at the bottom corners of the drape. This means that you will be mitering the corners. 

7. Sew a blind stitch to hold this in place.

8. Lay the lining side up, and then fold over the entire top edge in a 1-inch double fold. Pin the edge. Stitch in place, using a straight stitch.

9. Complete the drapes by attaching ring clips at the top. 

You are now ready to hang your curtains

How to make drapery curtain

Finding a set of draperies to match your décor can be difficult. You may find the right pattern, but the style isn't exactly what you had in mind or the material is too thin or too thick. 

 

Why don't you create your own lined window drapes? This is how we do that

 

1. Measure your windows to determine the length and width of the drapes. 

 

2. Hang your rings from the rod, and then measure from the base of the rings to the floor for the length. The width should match the width of the window.

3. Purchase the fabric for the drapes and your lining. Add 10 inches of fabric to the length measurement and double the width.

4. Prepare to sew the hems of your drape. Fold up the bottom of the drapery fabric 4 inches and iron. Then fold up another 4 inches and iron again.

5. Pin and sew the hem in place with a straight stitch. The hem should be at the top of the fold, approximately 4 inches from the bottom of the drape.

6. Cut the length and width of your lining. The width is the same width of the drape minus 6 inches. The length is the same length of the finished drape.

7. Fold up the bottom of the lining 2 inches and iron. Then fold up another 2 inches and iron again.Pin and sew the hem of the lining with a straight stitch. 

8. The hem should be at the top of the fold, approximately 2 inches from the bottom of the lining.

Drappery

Years ago, puddling the draperies on the floor actually made sure that air did not flow underneath. So, if we really want to keep the cold air out, we can consider puddling. 

How good are these treatments in the hot summer months? We have to keep heat out just as you do the cold. It has the same principal.

We can put also the layer like felt between the blackout liner and the drapery fabric. This tailors the drapery beautiful.

Less seems to be more in window treatments today. There are many choices in the shop or the interior designer. However, many people prefer to have simple designs, from a pretty valance to quilted shades or decorative shutters. And then they blend in with a room, rather than overwhelm it. 

One designer explains that before we choose what model we would like to put on our windows, we have to think firstly the function. Climate always comes up as an issue. We as the homeowner perhaps need something to keep the cold out? Many people want their window treatments to help cold air from coming in.

We can do this. You can put the heavy curtain and make it longer 3 or 4 inches beyond the windows to seal the air off. 

Blackout liners are another option. They can cut out air and light. You can put a layer of felt between the blackout and the drapery fabric. This tailors the drapery beautiful. It also helps  soundproof the room from any outside noise.

So we can have the aesthetic and function in the same time.

 

Simply beautiful with wood

Wood is always attractive for people. Its warmth and its  color bring the nature in the houses. 

There is never been an easier or more satisfying way to bring out the character and beauty of unfinished wood. Here is the ways to make your wooden furniture into its best look out.  With using Formby's Decorative Touches Woodcreme Matte Finish.

1. Clean up the wooden surface

2. You can sand, if it is dirty or still rough

3. Simply brush on the thick, no drip formula

4. After a few minutes, buff off for a soft and natural matte finish

5. Clean up is quick and easy with plain soap and water.

Try to have a product from the known brand, so won't be disappointed. Happy trying.